Skip to content
Appointment timing depends on ZIP code, route capacity, and access.
Call (310) 554-8899
Kenmore appliance service
Error Code

Kenmore Dishwasher F7E1 Error Code

Plain-language guidance for Kenmore code F7E1 (7-1) on Dishwasher — symptoms, safe checks, and when to call a technician.

Book a Repair (310) 554-8899
  • Upfront Estimates
  • Approval Before Repair
  • Expert Technicians
  • Workmanship Warranty

At a glance

Error code overview

A plain-language snapshot of F7E1 (7-1) for Kenmore Dishwasher — confirm the model series before you act.

Lena Hart Written by Lena Hart Appliance Repair Content Specialist Published October 20, 2026

Content status Verified

Error code F7E1 (7-1)
Appliance Dishwasher
Quick answer

F7E1 (7-1) on a Kenmore dishwasher: the heating element does not work, and the inspection and wiring steps from the manual.

Model compatibility

Kenmore reuses codes across series and model years, so F7E1 (7-1) may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

F7E1 means the heating element does not work.

When a Kenmore dishwasher shows F7E1 (7-1), the heating element is not working. The code is listed for the HE and Elite HE series with a digital display, for the Global HE, and for the MicroClean HE. Units without a display flash the Clean light in a function-problem pattern.

Steps for HE, Elite HE and Global HE

  1. Shut off power to the dishwasher.
  2. Look the heating element over, and replace it if it is visibly damaged.
  3. If it looks fine, check the wiring to the heating element.
  4. With the wiring intact, the heating element itself is replaced.

Steps for MicroClean HE

Unplug the dishwasher and inspect the element for visible damage first. If it looks intact, check the wiring between the electronic control board and the element, reconnect loose wires, and replace a damaged wire harness. Intact wiring leads to a new heating element.

Related codes

  • F7E2: heating element will not shut off
  • F6E6: incoming water too cold
  • F6E7: flow meter problem

Kenmore dishwasher service in Los Angeles

Still seeing the code? Our Los Angeles line for Kenmore dishwasher repair is (310) 554-8899. Read out the code and model number, and mention the steps you went through. Service information: Kenmore dishwasher repair.

Source: Kenmore Global HE dishwasher error codes; Kenmore MicroClean HE dishwasher error codes; Kenmore HE dishwasher error codes

Caution

Safety warning

Important safety warning

Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Get started

Seeing this code on your Kenmore appliance?

Book a specialist Kenmore service visit for a clear estimate and approval before any repair. Experienced technicians, clear diagnostics, and workmanship coverage on completed repairs.

Book a Repair (310) 554-8899
Fix it right

Recommended repair service

AE C1 C2 C3 C4 C5
Service areas

Available in these areas

Get started

Ready to restore your Kenmore appliance?

Book a repair online or call us — clear estimates, approval before any work, and a workmanship warranty on completed repairs.

Book a Repair (310) 554-8899

Book a repair

Tell us about your Kenmore we’ll take it from there

Share your model, symptom, and ZIP in Los Angeles County or Orange County and we’ll confirm an appointment. Prefer to talk? Call us during business hours.

(310) 554-8899
Phone (310) 554-8899
Email info@kenmorelosangeles.support
Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Kenmore appliance repair across Los Angeles County and Orange County.
Response time Appointment timing depends on ZIP code, route capacity, and access.