Skip to content
Appointment timing depends on ZIP code, route capacity, and access.
Call (310) 554-8899
Kenmore appliance service
Error Code

Kenmore Dishwasher F9E1 Error Code

Plain-language guidance for Kenmore code F9E1 (9-1) on Dishwasher — symptoms, safe checks, and when to call a technician.

Book a Repair (310) 554-8899
  • Upfront Estimates
  • Approval Before Repair
  • Expert Technicians
  • Workmanship Warranty

At a glance

Error code overview

A plain-language snapshot of F9E1 (9-1) for Kenmore Dishwasher — confirm the model series before you act.

Lena Hart Written by Lena Hart Appliance Repair Content Specialist Published October 20, 2026

Content status Verified

Error code F9E1 (9-1)
Appliance Dishwasher
Quick answer

F9E1 (9-1) on Kenmore dishwashers: a long drain on 665-prefix models, or an undetected diverter disc position on HE-series units.

Model compatibility

Kenmore reuses codes across series and model years, so F9E1 (9-1) may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Plain language

What this code means

F9E1 means a long drain (665-prefix models) or that the control board cannot detect the diverter disc position.

F9E1 (9-1) is read two ways on Kenmore dishwashers.

Models with a 665 prefix: long drain

The dishwasher takes too long to empty its water. The owner checks are to clean the filter, check the drain hose, the disposer knockout plug and the air gap, and then cycle power for 30 seconds.

HE, Elite HE, Global HE and MicroClean HE: diverter disc

The electronic control board cannot detect the position of the diverter disc. The diverter motor positions that disc so water goes to the lower or upper spray arm, and it reports the disc position back to the board. Unplug the dishwasher and check the wiring going to the diverter motor. Loose wires are reconnected and a damaged harness replaced. If the wiring is intact, the diverter motor is replaced, because it is not sending position signals. Units without a digital display flash the Clean light.

Related codes

  • F9E2: diverter motor stuck on
  • F9E3: diverter disc missing
  • F8E1: slow drain

Kenmore dishwasher service in Los Angeles

Still seeing the code? Our Los Angeles line for Kenmore dishwasher repair is (310) 554-8899. Read out the code and model number, and mention the steps you went through. Service information: Kenmore dishwasher repair.

Source: Kenmore Global HE dishwasher error codes; Kenmore MicroClean HE dishwasher error codes; Kenmore HE dishwasher error codes; Dishwasher error codes product help

Caution

Safety warning

Important safety warning

Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Get started

Seeing this code on your Kenmore appliance?

Book a specialist Kenmore service visit for a clear estimate and approval before any repair. Experienced technicians, clear diagnostics, and workmanship coverage on completed repairs.

Book a Repair (310) 554-8899
Fix it right

Recommended repair service

AE C1 C2 C3 C4 C5
Service areas

Available in these areas

Get started

Ready to restore your Kenmore appliance?

Book a repair online or call us — clear estimates, approval before any work, and a workmanship warranty on completed repairs.

Book a Repair (310) 554-8899

Book a repair

Tell us about your Kenmore we’ll take it from there

Share your model, symptom, and ZIP in Los Angeles County or Orange County and we’ll confirm an appointment. Prefer to talk? Call us during business hours.

(310) 554-8899
Phone (310) 554-8899
Email info@kenmorelosangeles.support
Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Kenmore appliance repair across Los Angeles County and Orange County.
Response time Appointment timing depends on ZIP code, route capacity, and access.